Phone: +49 5108 3555     
Direct push water sampler
The direct push (DP) procedure is a cheap alternative to often expensive methods to receive a groundwater sample. Our water sampler types S-9097, DP 32/42 and DP 36/48 are designed for the DP procedure.

The water sampler is driven into the investigation depth. Water enters the system through a filter and is pumped up through a hose. This cheap system is mainly used to determine contaminations from contaminated sites, as well as for site investigations. Expensive and complex gauge excavations can be avoided using the DP water sampler instead.

Water sampler S-9097
The water sampler S-9097 allows, a cost-effective sampling of the groundwater and capillary space. The water sampler S-9097 is driven by hand or with help of a device into the investigation depth. A replaceable external filter allows water to enter the filter tube. Via an hose, which slides through the hollow rod, this water can be pumped up. The passage in the hollow rod is 12 mm.

With help of the foot valve pump S-60, water can be pumped up from a depth of up to 20 m. After samples are taken from one depth, the sampler can be driven further in for additional groundwater tests. Efficient applications are the determination of contaminations and their spreading, as well as for soil survey tests.

Water sampler S-9097 Catalog page 51
Double steel ram filter S-9097 Catalog page 50
Steel ram filter S-9097 - 450 mm Catalog page 50

Water sampler DP 32/42
System with external filter: Through an external filter, water flows into the sampling device. The hose is lowered through the hollow rod and water can be pumped up.

System with internal filter: The closed system is driven into the depth of investigation. Then the ejection rod with inner extension rod is inserted into the hollow rod. The lost probing cone is ejected and the internal filter is extended into the groundwater. Following sampling the water can be pumped out again.
Water sampler DP 32/42 - external filter Catalog page 52
Water sampler DP 32/42 - internal filter Catalog page 52

Water sampler DP 36/48
This water sampler is available with external or internal filter system. Differences to the water sampler DP 32/42 are the larger sized probing rod and the RDS connection.

Both water sampling and soil sampling can be performed using RDS connection and associated probing equipment. One probing rod can be used for both applications.
Water sampler DP 36/48 - external filter Catalog page 53
Water sampler DP 36/48 - internal filter Catalog page 53
Water sampler PVC glass
An easy, quick and reuseable system to take water samples from wells and observation pipes.

Diameter Volume Length
Water sampler with ∅ 25 350 mm 1135 mm Catalog page 54
Water sampler with ∅ 32 200 mm 515 mm Catalog page 54
Water sampler with ∅ 32 550 mm 1135 mm Catalog page 54
Water sampler with ∅ 40 300 mm 515 mm Catalog page 54
Water sampler with ∅ 40 550 mm 790 mm Catalog page 54

Membrane pump OD 25 mm
Application: Sampling of liquids from open water, wells and observation pipes.

The membrane pump made of PVC glass is lowered to the investigation depth. After immersion of the pump, water enters through the valve into the hose. By moving the hose up and down the water is pumped up.

Furthermore, the membrane pump can be used as a water sampler with a volume of ca. 350 ml. The valve in the lower part opens when lowered into the sample fluid and closes when the pump is moved up.
Membrane pump OD 25 mm Catalog page 54

Piston sampler
The piston sampler is applied to take soil samples from below groundwater level and for sandy sediment samples. The piston inside the tube is pulled up manually by using a piston rod it generates a negative pressure to retain the soil sample in the tube. The piston also serves to push out the soil sample.
Diameter Length
Piston sampler with ∅ 40x1 mm 1000 mm Catalog page 55
Piston sampler with ∅ 40x1 mm 2000 mm Catalog page 55

Sediment corer
Sediment corer is applied to take soft and muddy sediment samples. The sediment corer is extenable and can be used by hand in shallow shore areas or in deep water.

When lowered the integrated valve opens, no backwater occurs. The sediment corer pierces the ground. When lifted the valve closes. The resulting negative pressure retains the sediment sample in the tube.
Sediment corer ∅ 50 mm Catalog page 55
Battery peristaltic pump
Battery operated peristaltic pump for liquids and gases. The peristaltic pump has a flow rate of ca. 0-2,3 l/min and works up to suction depth of 6-7 m. The flow rate is adjustable.

The fully charged battery lasts up to ca. 8 hours.
Battery peristaltic pump Catalog page 56

Hand operated peristaltic pump
Hand operated peristaltic pump for liquids and gases. Using a crank, it works in an operation depth up to 9 m. The silicone hose is closed by at least one roll. Therefore liquids and gases cannot flow back.
Hand operated peristaltic pump Catalog page 56

Peristaltic pump SL-10
This peristaltic pump is designed for the „Direct Push (DP)“ procedure. By a foot valve pump and PE hose, liquids can be pumped up.

The peristaltic pump is connected by a quick-release system with PE hose ∅ 10 mm. A pump support pin allows to use the peristaltic pump directly with 2“ gauge tubes.
Peristaltic pump SL-10 Catalog page 57
Foot valve pump
In cases where the use of common pumps is not adequate or effective, these foot valve pumps made of stainless steel can be used to pump up groundwater.

The foot valve pump is connected to the hose. When the foot valve pump is immersed in water, water enters the hose. Through an oscillating movement, water is pumped up. Escape of volatile organic substances is restricted to a minimum.
External diameter Hose size
Foot valve pump with ∅ 11 mm ∅ 10x1 mm Catalog page 57
Foot valve pump with ∅ 12 mm ∅ 10x1 mm Catalog page 57
Foot valve pump with ∅ 13 mm ∅ 12x1 mm Catalog page 57
Foot valve pump with ∅ 18 mm ∅ 16x2 mm Catalog page 57
Electric contact meter
Electric contact meter allows a quick and easy measurement of water levels. Used in wells, tanks, drilling holes and to control pumping tests.

Available with visual and acoustic signal.

Electric contact meter with plummet diameter 12 mm and 15 mm are also available with frame stand.
Length Plummet ∅
Electric contact meter with 15 m 10 mm Catalog page 58
Electric contact meter with 15 m 12 mm Catalog page 58
Electric contact meter with 30 m 12 mm Catalog page 58
Electric contact meter with 15 m 15 mm Catalog page 58
Electric contact meter with 30 m 15 mm Catalog page 58
HDPE filter tubes
The trapezodial threads TR and TRN are not compatible. TRN comes with smaller filter segment and bigger length tolerances. Slot width is ca. 0,3 mm.
Thread Dimensions
Filter tube with TR ∅ 32x1000 mm Catalog page 60
Filter tube with TR ∅ 40x1000 mm Catalog page 60
Filter tube with TR ∅ 63x1000 mm Catalog page 60
Filter tube with TRN ∅ 32x1000 mm Catalog page 60
Filter tube with TRN ∅ 50x1000 mm Catalog page 60

HDPE attachment tubes
Without slots. TRN has bigger length tolerances.
Thread Dimensions
Attachment tube with TR ∅ 32x1000 mm Catalog page 60
Attachment tube with TR ∅ 40x1000 mm Catalog page 60
Attachment tube with TR ∅ 63x1000 mm Catalog page 60
Attachment tube with TRN ∅ 32x1000 mm Catalog page 60
Attachment tube with TRN ∅ 50x1000 mm Catalog page 60

HDPE cone with external thread
For closing gauge tubes.
External Thread Diameter
Cone with TR ∅ 32 mm Catalog page 60
Cone with TR ∅ 40 mm Catalog page 60
Cone with TR ∅ 63 mm Catalog page 60
Cone with TRN ∅ 32 mm Catalog page 60
Cone with TRN ∅ 50 mm Catalog page 60

HDPE caps with internal thread
For closing gauge tubes.
Internal thread Diameter
Cap with TR ∅ 32 mm Catalog page 61
Cap with TR ∅ 40 mm Catalog page 61
Cap with TR ∅ 63 mm Catalog page 61

Plug cap with lid
To plug on top of gauge tubes.
Diameter
Plug cap with ∅ 32 mm Catalog page 61
Plug cap with ∅ 40 mm Catalog page 61
Plug cap with ∅ 50 mm Catalog page 61

Plugs
For closing gauge tubes. The plug is simply inserted into the gauge tube. Using a hex wrench, the plug is clamped in the gauge tube by the clamp system. No connection thread is required on the tube.

Diameter
Plug with ∅ 32 mm Catalog page 61
Plug with ∅ 40 mm Catalog page 61
Plug with ∅ 50 mm Catalog page 61
Plug with ∅ 63 mm Catalog page 61

Adapter TR - inch thread
For connecting trapezodial thread with inch thread.
Internal thread External thread
Adapter with TR ∅ 32 mm 1" Catalog page 61
Adapter with TR ∅ 40 mm 1 1/4" Catalog page 61
Adapter with TR ∅ 63 mm 2" Catalog page 61

> Geotechnical equipment
> Production and sale
> Ball clamps
> Extension rods
> Hand drilling devices
> Soil investigation equipment
> Window sampler
> Rod pullers
> Dynamic probing
> Water Samplers
> Well construction material
> Pneumatic dynamic penetrometer
Company: Stitz GmbH
Street: Nikolaus-Otto-Straße 1
ZIP/City: 30989 Gehrden, Germany
Email: info@stitz-gmbh.de
Phone: +49 5108 3555
Fax: +49 5108 3500
© Copyright Stitz GmbH Home Contact Imprint & Privacy